Skip to main content

FC - Primer Selection Guide (ENG)

Choose the right Forcrete primer for the substrate and for the base coat that goes on top.

tomas martinsson
Updated by tomas martinsson
Professional Guide / Primer Systems

Primer Selection — Forcrete

Select the appropriate primer based on substrate conditions and the subsequent base coat system.

💡 About Primers:
Primers bind surface dust, regulate substrate porosity, and ensure reliable adhesion for microcement systems. Choosing the correct primer depends on the substrate material and the subsequent system layer to be applied.
🛑 Before You Begin:
• The substrate must always be sound, dry, and free of dust, grease, and loose particles.
• Always allow the primer to dry or fully cure before proceeding to the next step.
• When broadcasting quartz sand, broadcast generously into the wet primer to full saturation. Sweep and vacuum away all unbonded sand before troweling.

1. Wall Primers (Monostone & Rockplaster)

Monoprime

Fast-drying primer for absorbent walls (plasterboard, render, and absorbent boards) prior to applying Monostone XL or L (Rockplaster).

⏱️ Drying Time: approx. 30–60 min | ⚖️ Coverage: approx. 50–70 g/m²
Instructions: Apply Monoprime ↗
Monogrip

Green/blue ready-mixed adhesion grip primer with silica aggregate for painted walls, vinyl, and abraded tiles prior to applying Monostone XL or L (Rockplaster).

⏱️ Drying Time: approx. 30–60 min | ⚖️ Coverage: approx. 100 g/m²
Instructions: Apply Monogrip ↗

2. Epoxy Primers for Floors, Concrete & Tiles

Forprime DPM

2-component epoxy primer for tiled floors, vinyl, and worktops where maximum adhesion is required.

⏱️ Cure Time: 6–24 hours | ⚖️ Coverage: 120–150 g/m²
Instructions: Apply Forprime DPM ↗
Forprime EPST

Combined primer and base layer for concrete and self-leveling screed when troweling mesh and priming in a single step.

⏱️ Cure Time: min. 12 hours | ⚖️ Coverage: approx. 750 g/m² (Always sand-broadcasted)
Instructions: Apply Forprime EPST ↗

3. Primer for Decorative Walls (Prior to XT & Coarse)

Forprime EPWB

Waterborne 2-component epoxy primer for absorbent walls on dry, decorative surfaces prior to applying Microbase XT or Microquartz Coarse.

⏱️ Apply Next Layer: 30–120 minutes | ⚖️ Coverage: 60–100 g/m²
Instructions: Apply Forprime EPWB ↗

4. Quick Reference: Substrate to Primer Matrix

Substrate
Primer
Subsequent Layer
Sand Broadcast?
Concrete & Screed (Floor)
Forprime EPST
Forprime HB / Microbase XT
Yes, always
Tiled Floors & Vinyl (Floor)
Forprime DPM
Forprime HB / Microbase XT
Yes, if XT
Plasterboard & Render (Wall)
Monoprime
Monostone XL / L
No
Painted Walls & Vinyl (Wall)
Monogrip
Monostone XL / L
No
Absorbent Wall (Decorative)
Forprime EPWB
Microbase XT / Microquartz
No
⏳ Drying Times: Monoprime and Monogrip dry in approximately 30–60 minutes. Apply over Forprime EPWB within 30–120 minutes. Forprime DPM and EPST cure in 6–24 hours before applying the subsequent layer.

How did we do?

FC - Application on Waterproofing Membranes (ENG)

FC - Reinforcement & Preparation (ENG)