FC - Reinforcement & Preparation (ENG)
How to choose and fit 160 g fibreglass mesh for Forcrete on floors, walls and worktops, and how to handle corners.
Updated
by tomas martinsson
Guide / Reinforcement
Forcrete — Reinforcement
Instructions for mesh selection, installation, and corner detailing for crack-resistant floor, wall, and worktop installations.
💡 About the Reinforcement Mesh:
Proper reinforcement is a prerequisite for tensile strength and long-term crack resistance. We exclusively use 160 g fiberglass mesh for all reinforced installations. Lighter or finer mesh fabrics do not provide adequate structural tensile strength and must not be used.
Proper reinforcement is a prerequisite for tensile strength and long-term crack resistance. We exclusively use 160 g fiberglass mesh for all reinforced installations. Lighter or finer mesh fabrics do not provide adequate structural tensile strength and must not be used.
📱 Specifications & Installation:
• Mesh Grade: 160 g/m² alkali-resistant fiberglass mesh.
• Installation: Spot-glued directly to the primed substrate using a hot-melt glue gun.
• Jointing: Runs must always be installed strictly butt-jointed (edge-to-edge) without overlapping.
• Applications: Bathrooms (floors and walls), tiled floors, worktops, and all other substrates requiring reinforcement.
• Mesh Grade: 160 g/m² alkali-resistant fiberglass mesh.
• Installation: Spot-glued directly to the primed substrate using a hot-melt glue gun.
• Jointing: Runs must always be installed strictly butt-jointed (edge-to-edge) without overlapping.
• Applications: Bathrooms (floors and walls), tiled floors, worktops, and all other substrates requiring reinforcement.
🛑 Critical Installation Rules:
• Always Butt-Joint Edge-to-Edge: The mesh must never be overlapped. Because microcement is applied in millimeter-thin layers, any overlap creates a local elevation that will telegraph through as a visible ridge in the finished surface.
• Never Wrap Around Corners: Always cut or trim the mesh cleanly right at the corner junction. Rounding mesh around a corner results in rounded, poorly defined corners. Reinforce corners with corner mesh strips only if specifically desired. We advise against this, as our experience shows that any structural movement then risks pulling stress cracks further out onto the wall surface, making them significantly harder to repair than if tension is confined to the corner junction.
• Always Butt-Joint Edge-to-Edge: The mesh must never be overlapped. Because microcement is applied in millimeter-thin layers, any overlap creates a local elevation that will telegraph through as a visible ridge in the finished surface.
• Never Wrap Around Corners: Always cut or trim the mesh cleanly right at the corner junction. Rounding mesh around a corner results in rounded, poorly defined corners. Reinforce corners with corner mesh strips only if specifically desired. We advise against this, as our experience shows that any structural movement then risks pulling stress cracks further out onto the wall surface, making them significantly harder to repair than if tension is confined to the corner junction.
1. Step-by-Step Installation
1.
Substrate Inspection: Ensure the primer has dried or cured completely and that the surface is clean and free of debris.
2.
Roll Out and Cut: Unroll the mesh across the surface and cut the sheets to length. Ensure the mesh lies completely flat without ripples or folds.
3.
Spot-Glue in Place: Secure the mesh to the substrate using small dots of hot-melt glue (glue gun). Space the glue spots closely enough so the mesh does not lift or slide during troweling.
4.
Butt-Joint: Position the next sheet flush against the previous one, strand against strand, ensuring no overlapping occurs.
2. Internal & External Corners
Trim Cleanly at Junctions
• Internal Corners: Cut the mesh cleanly along the internal corner line. Do not allow the mesh to bridge onto the adjoining wall. Trowel neatly up to the corner line.
• External Corners & Niches: Trim the mesh along the corner edge. Apply the base coat using a flat trowel or steel spatula to keep the layer strictly within grain thickness and prevent excessive material buildup at the angles.
• External Corners & Niches: Trim the mesh along the corner edge. Apply the base coat using a flat trowel or steel spatula to keep the layer strictly within grain thickness and prevent excessive material buildup at the angles.
3. Next Steps
Once the mesh is installed, proceed with the base coat application based on your chosen system:
How did we do?
FC - Primer Selection Guide (ENG)
FC - Substrate Preparation on Tiles (ENG)