Skip to main content

FC - Forprime EPWB (ENG)

Water-based epoxy primer for absorbent and painted walls in dry, decorative areas, before Microquartz or Microbase XT.

tomas martinsson
Updated by tomas martinsson
Guide / Epoxy Primer

Forcrete — Forprime EPWB

Guide for mixing and application of water-based 2-component epoxy primer prior to Microbase XT and Microquartz on decorative surfaces.

💡 About Forprime EPWB:
Forprime EPWB is a water-based 2-component epoxy primer providing excellent adhesion on absorbent and painted wall surfaces. It is used in decorative installations (non-wet rooms) where you apply Microbase XT or Microquartz directly onto the substrate in 2 coats without reinforcement mesh.
📱 Coverage & Mixing Ratio:
• Mixing Ratio (A : B): 75 parts Component A to 25 parts Component B (75 : 25). Always weigh using precision scales.
• Material Consumption: Approx. 60–100 g/m² per coat.
• Application Tool: Apply using a short-pile roller or microfiber roller.
Always use the mixing app to calculate material quantities and exact proportions for your project.
⚠️ Important Information Before Starting:
• Working Temperature: Material, substrate, and ambient air temperatures must remain between +10 °C and +25 °C.
• Pot Life in Bucket: Approx. 60 minutes at +20 °C.
• Application Window for Troweling: Apply the first microcement coat 30–120 minutes after rolling the primer.
• Storage: Store frost-free. Shelf life is 12 months in unopened original packaging.
🛑 Decorative Environments Only:
This system method with Forprime EPWB and 2 coats of microcement without mesh is strictly limited to dry, decorative feature walls. This system must never be used in bathrooms or other wet areas where reinforcement mesh and an approved full waterproofing system are required.

1. Substrate Preparation

1.
Surface Inspection: The substrate must be sound, dry, and clean from dust, oil, and grease.
2.
Substrate Abrasion: Sand painted surfaces to a dull, matte finish to ensure optimal mechanical adhesion. Scrape away loose particles on plasterboard and absorbent boards. Vacuum the surface thoroughly.

2. Step-by-Step Mixing

🛑 Critical Mixing Precaution – Component B Spills:
It is critical to avoid spilling or splashing unmixed Component B onto floor or wall surfaces. It will not cure independently, and microcement applied over contaminated areas will fail to cure properly. Always mix on protective floor covering or in a separate prep area.
1.
Weigh Components: Weigh out 75 parts Component A and 25 parts Component B into a clean bucket placed on protective floor covering.
2.
Mix: Blend using a mechanical paddle mixer at low speed (300–400 rpm) for at least 3 minutes until completely homogeneous.

3. Application & Workflow

Roll and Trowel Wall by Wall
• Rolling the Primer: Pour the primer into a roller tray and apply an even, fully covering coat across the surface. Avoid puddles, runs, and excessive buildup.
• Workflow Strategy: Because the microcement must be applied within 30–120 minutes after rolling, roll one wall at a time and trowel it before moving on to the next wall section.
• Troweling: Trowel the first coat of Microbase XT or Microquartz directly onto the primed wall within the designated application window (30–120 minutes).

4. Next Steps

Select which product you are applying over Forprime EPWB:

🛑 Health & Safety Equipment:
• Product contains epoxy resin and may cause skin irritation upon contact.
• Always wear chemical-resistant nitrile gloves during mixing and rolling.
• Wear safety glasses/goggles during paddle mixing.
• Ensure continuous, adequate workspace ventilation and keep out of reach of children.
⏱️ Curing & Tool Maintenance (+20 °C):
• Trowel Microcement: Within 30–120 minutes.
• Tool Cleaning: Clean rollers, paint trays, and mixer paddle with water or solvent wipes immediately after use before the primer cures.

Documents & Technical Datasheets

How did we do?

FC - Forprime EPST (ENG)

FC - Forprime HB/FL (ENG)