FC - Monostone XL / L (Rockplaster) (ENG)
Resin-based one-component wall cement. XL as a base coat or coarser finish, L for a smoother finish (Rockplaster).
Updated
by tomas martinsson
Guide / Wall Systems
Forcrete — Monostone XL / L (Rockplaster)
Comprehensive guide for preparation, mixing, application, and drying of Monostone XL and L wall microcement.
💡 About Monostone XL & L:
Monostone is a 1-component, resin-based microcement system formulated specifically for walls. Monostone XL is used as a base coat embedded with reinforcement mesh or as a textured final finish. Monostone L features finer aggregates and is used for a smoother final finish. When utilized as a decorative final coat, the product is referred to as Rockplaster.
Monostone is a 1-component, resin-based microcement system formulated specifically for walls. Monostone XL is used as a base coat embedded with reinforcement mesh or as a textured final finish. Monostone L features finer aggregates and is used for a smoother final finish. When utilized as a decorative final coat, the product is referred to as Rockplaster.
📱 Coverage & Specifications:
• Monostone XL: Approx. 0.9–1.4 kg/m² per coat (approx. 1.4 kg/m² when embedding mesh / approx. 0.9 kg/m² as second coat).
• Monostone L: Approx. 0.6–0.8 kg/m² per coat.
• Layer Thickness: Always apply tightly in grain thickness (approx. 0.5–1.0 mm per coat).
Always use the mixing app to calculate the exact water and pigment ratios required for your surface area.
• Monostone XL: Approx. 0.9–1.4 kg/m² per coat (approx. 1.4 kg/m² when embedding mesh / approx. 0.9 kg/m² as second coat).
• Monostone L: Approx. 0.6–0.8 kg/m² per coat.
• Layer Thickness: Always apply tightly in grain thickness (approx. 0.5–1.0 mm per coat).
Always use the mixing app to calculate the exact water and pigment ratios required for your surface area.
🛑 Critical: Preventing Stress Cracks and Failures:
• Tiles & Grout Lines: Monostone XL can only be applied directly over tiles (post-priming) if the grout joints are narrow and preferably on large-format tiles. The product is not formulated to level significant substrate unevenness. On smaller tiles or deep joints, the risk of applying an excessively thick layer increases significantly. Deep grout lines and irregularities must always be pre-leveled using a cementitious repair mortar.
• Thickness: Always apply strictly to grain thickness (max 0.5–1.0 mm). Exercise extreme caution in internal corners, niches, angles, and transitions where material tends to accumulate; excessive thickness creates structural tension and failure risks.
• Air Circulation Fans: Monostone dries from the surface inward and may feel dry to the touch while retaining critical trapped moisture. Always run circulation fans when leaving the site and upon arrival—this ensures drying is not compromised by high ambient humidity or closed doors.
• Humid Seasons: Late summer, autumn, or humid weather patterns extend curing times—forced air circulation with fans is mandatory year-round.
• Moisture Limit < 4% (Do Not Seal): The surface must not be sealed or overlaid with Microquartz Coarse until the moisture content is confirmed below 4%. Trapped moisture creates severe structural tension that will result in cracking 6–18 months post-installation.
• Tiles & Grout Lines: Monostone XL can only be applied directly over tiles (post-priming) if the grout joints are narrow and preferably on large-format tiles. The product is not formulated to level significant substrate unevenness. On smaller tiles or deep joints, the risk of applying an excessively thick layer increases significantly. Deep grout lines and irregularities must always be pre-leveled using a cementitious repair mortar.
• Thickness: Always apply strictly to grain thickness (max 0.5–1.0 mm). Exercise extreme caution in internal corners, niches, angles, and transitions where material tends to accumulate; excessive thickness creates structural tension and failure risks.
• Air Circulation Fans: Monostone dries from the surface inward and may feel dry to the touch while retaining critical trapped moisture. Always run circulation fans when leaving the site and upon arrival—this ensures drying is not compromised by high ambient humidity or closed doors.
• Humid Seasons: Late summer, autumn, or humid weather patterns extend curing times—forced air circulation with fans is mandatory year-round.
• Moisture Limit < 4% (Do Not Seal): The surface must not be sealed or overlaid with Microquartz Coarse until the moisture content is confirmed below 4%. Trapped moisture creates severe structural tension that will result in cracking 6–18 months post-installation.
1. Primer & Substrate
The surface must always be primed prior to troweling Monostone. Select the appropriate primer for your substrate:
2. Substrate Preparation
1.
Substrate Inspection: The wall substrate must be structurally sound, dry, and free of dust, grease, and loose particles.
2.
Tiled Substrates: Large, flush tiles with narrow joints do not require pre-leveling following grinding and Monogrip application. Small format tiles, deep/wide joints, or uneven surfaces must always be pre-leveled flush using a cementitious compound first to avoid excessive Monostone layer thickness.
3. Mixing & Pigmentation
🧪 Mixing Monostone:
• Add 50–200 g of clean water together with the pigment powder directly into the bucket.
• Mix thoroughly with a mechanical paddle mixer at medium speed for at least 2–3 minutes until pigments are completely dispersed and the mixture is uniform.
• Being a 1-component cement, it is ready for immediate application without slake time. Keep the bucket covered between passes to prevent premature crusting.
• Add 50–200 g of clean water together with the pigment powder directly into the bucket.
• Mix thoroughly with a mechanical paddle mixer at medium speed for at least 2–3 minutes until pigments are completely dispersed and the mixture is uniform.
• Being a 1-component cement, it is ready for immediate application without slake time. Keep the bucket covered between passes to prevent premature crusting.
4. Application Procedures
Option 1: Decorative Feature Walls (2 coats without mesh)
• Coat 1 (XL or L): Trowel tightly in grain thickness over 1–2 m² sections at a time. Immediately smooth over using a flexible spatula to remove trowel lines and chatter marks. Allow to dry for 30–60 minutes assisted by a fan.
• Coat 2 (XL or L): Apply the second coat in the same manner. Work the surface with a plastic trowel after a few minutes if a distinct, stony texture is desired.
• Sealing: Lightly sand as needed and seal with Monoseal or Forshield 2KWB.
• Coat 2 (XL or L): Apply the second coat in the same manner. Work the surface with a plastic trowel after a few minutes if a distinct, stony texture is desired.
• Sealing: Lightly sand as needed and seal with Monoseal or Forshield 2KWB.
Option 2: Bathrooms & Tiled Walls (3 coats with mesh)
• Coat 1 (Monostone XL + Mesh): Place 160 g fiberglass mesh and embed it with Monostone XL. Immediately smooth over with a flexible spatula to eliminate ridges. Allow to dry for at least 1–2 hours assisted by a fan.
• Coat 2 (Monostone XL): Apply an opaque second coat of XL to fully bury the mesh pattern. Sand either Coat 1 or Coat 2 thoroughly with a 40 or 50 grit diamond pad to prevent telegraphing of the mesh.
• Coat 3 (Final Finish XL or L): Apply the final decorative coat and compact with a plastic trowel if desired.
• Sealing: Sand lightly and seal with 2 coats of Forshield 2KWB.
• Coat 2 (Monostone XL): Apply an opaque second coat of XL to fully bury the mesh pattern. Sand either Coat 1 or Coat 2 thoroughly with a 40 or 50 grit diamond pad to prevent telegraphing of the mesh.
• Coat 3 (Final Finish XL or L): Apply the final decorative coat and compact with a plastic trowel if desired.
• Sealing: Sand lightly and seal with 2 coats of Forshield 2KWB.
Option 3: Base Layer for Microquartz (Walls Only)
• Coat 1 (Monostone XL + Mesh): Position 160 g mesh and embed using Monostone XL. Immediately smooth out using a flexible spatula to eliminate ridges. Allow to dry for at least 1–2 hours with forced air circulation.
• Coat 2 (Monostone XL): Trowel an opaque layer of XL to cover the mesh weave entirely. Sand either Coat 1 or Coat 2 thoroughly using a 40 or 50 grit diamond pad to ensure the mesh profile is eliminated.
• Drying Prior to Microquartz: The surface must cure under continuous fan-assisted ventilation until fully dry (< 4% moisture content) before applying Microquartz Coarse. Never cover the substrate before this threshold is verified.
• Coat 2 (Monostone XL): Trowel an opaque layer of XL to cover the mesh weave entirely. Sand either Coat 1 or Coat 2 thoroughly using a 40 or 50 grit diamond pad to ensure the mesh profile is eliminated.
• Drying Prior to Microquartz: The surface must cure under continuous fan-assisted ventilation until fully dry (< 4% moisture content) before applying Microquartz Coarse. Never cover the substrate before this threshold is verified.
💡 Pro Tip for Crisp Internal & External Corners (Final Coat):
To execute razor-sharp corners easily with Monostone / Rockplaster, tape off the adjacent walls at the corner prior to applying the final coat. Proceed with the application on the active wall, then repeat on opposite walls.
• Remove masking tape immediately once the active wall is troweled.
• Position a fan directly facing the freshly finished wall.
• Sand and re-tape: After a few hours, lightly sand the corner transitions on the cured walls, mask them, and apply the final coat to the remaining adjacent walls.
This technique works equally well on internal and external corners. While optional, it greatly simplifies achieving sharp, professional junctions.
To execute razor-sharp corners easily with Monostone / Rockplaster, tape off the adjacent walls at the corner prior to applying the final coat. Proceed with the application on the active wall, then repeat on opposite walls.
• Remove masking tape immediately once the active wall is troweled.
• Position a fan directly facing the freshly finished wall.
• Sand and re-tape: After a few hours, lightly sand the corner transitions on the cured walls, mask them, and apply the final coat to the remaining adjacent walls.
This technique works equally well on internal and external corners. While optional, it greatly simplifies achieving sharp, professional junctions.
5. Sanding & Next Steps
Read more about sanding protocols or proceed to the dedicated guides for your selected finish:
🛑 Health & Safety Equipment:
• Wear protective chemical/work gloves when mixing and troweling.
• Use safety goggles during mechanical paddle mixing.
• Wear an approved particulate respirator mask during sanding operations.
• Ensure continuous, adequate workspace ventilation and keep out of reach of children.
• Use safety goggles during mechanical paddle mixing.
• Wear an approved particulate respirator mask during sanding operations.
• Ensure continuous, adequate workspace ventilation and keep out of reach of children.
⏱️ Drying Times & Tool Maintenance:
• Drying Time Between Coats: Approx. 30–60 minutes assisted by forced fan ventilation.
• Prior to Sealing / Microquartz: Minimum 12–24 hours assisted by a fan until completely cured (< 4% moisture).
• Cleaning: Clean tools and mixing vessels immediately with clean water following use.
• Drying Time Between Coats: Approx. 30–60 minutes assisted by forced fan ventilation.
• Prior to Sealing / Microquartz: Minimum 12–24 hours assisted by a fan until completely cured (< 4% moisture).
• Cleaning: Clean tools and mixing vessels immediately with clean water following use.
Documents & Technical Datasheets
📄 Technical Documentation: Forcrete Monostone XL / L
How did we do?
FC - Monoprime (ENG)
FC - Trowel X Base & L (ENG)