DC - Titan Presealer / Titan Cream (ENG)
Pre-treatment before Titan Topsealer that saturates the microcement, prevents stains and gives the sealer a key.
Updated
by tomas martinsson
Product Guide / Pre-sealer
Pre-treatment: Titan Presealer / Titan Cream
Saturate the substrate with pre-sealer before topcoating. This ensures optimal adhesion and prevents blotches in the microcement.
đ Before You Begin:
âą Substrate & Cleanliness: Ensure the surface is sound, dry, and free from dirt, oil, and grease.
âą Microcement Drying Time: Apply the pre-sealer no earlier than 24 hours after the final coat of microcement has dried.
âą Rising Damp: We advise against microcement on substrates subject to rising damp. Basements must be properly drained, insulated, or completely dry.
⹠Working Temperature: Ambient room and substrate temperatures must remain between +10 °C and +25 °C throughout.
âą Substrate & Cleanliness: Ensure the surface is sound, dry, and free from dirt, oil, and grease.
âą Microcement Drying Time: Apply the pre-sealer no earlier than 24 hours after the final coat of microcement has dried.
âą Rising Damp: We advise against microcement on substrates subject to rising damp. Basements must be properly drained, insulated, or completely dry.
⹠Working Temperature: Ambient room and substrate temperatures must remain between +10 °C and +25 °C throughout.
1. Roller Selection and Pre-sealer Options
Titan Presealer
Standard
Standard primer prior to Titan Topsealer on walls and floors in dry areas. Saturates the surface and regulates porosity.
âą Dry Areas: Dilute with 10% clean water. Apply 1 coat.
âą Wet Zones / Bathroom Walls: Apply 2 coats (dilute coat 1 with 20%, coat 2 with 10%). Allow 2â3 hours drying time between coats.
âą Wet Zones / Bathroom Walls: Apply 2 coats (dilute coat 1 with 20%, coat 2 with 10%). Allow 2â3 hours drying time between coats.
Titan Cream
Bathroom Floors
Recommended for bathroom floors if using the Titan sealer system instead of Topsealer Dragon (which offers slightly higher resistance against heavy wear and standing water).
âą Dilution: Always dilute with 20% clean water.
âą Application: Apply 1 even, saturating coat to provide enhanced protection against water spotting prior to topcoating.
âą Application: Apply 1 even, saturating coat to provide enhanced protection against water spotting prior to topcoating.
2. Preparation and Sanding
3. Application
đ Critical Application Rules â Direct Sunlight and Floor Protection:
âą No Direct Sunlight: Never apply in direct sunlight, as the heat causes the pre-sealer to dry prematurely and develop lap lines. Mask off windows or schedule application when direct sunlight is not hitting the surface.
âą Protect Floors in Bathrooms: The floor must be masked off when sealing walls in bathrooms, especially during the first coat. Drips and spills absorb instantly into unsealed microcement and leave permanent dark spots. Always place the paint tray on masking paper during floor application.
âą No Direct Sunlight: Never apply in direct sunlight, as the heat causes the pre-sealer to dry prematurely and develop lap lines. Mask off windows or schedule application when direct sunlight is not hitting the surface.
âą Protect Floors in Bathrooms: The floor must be masked off when sealing walls in bathrooms, especially during the first coat. Drips and spills absorb instantly into unsealed microcement and leave permanent dark spots. Always place the paint tray on masking paper during floor application.
4. Next Steps: Topcoat Sealer
Once the pre-treatment has dried, apply the final topcoat:
Documents and Technical Datasheets
đ Technical Documentation: Titan Presealer / Pre-sealer
- Technical Datasheet (TDS) (PDF) â
- Safety Datasheet (SDS): Coming soon, contact Designcement to receive it.
đĄïž Health & Safety Equipment & Tool Care:
âą Protective Equipment: Wear protective gloves and safety goggles during handling and dilution. Wear respiratory protection during all sanding stages.
âą Cleaning: Clean tools and brushes thoroughly with water immediately after use before the material starts drying. For dried residue, clean tools with acetone or wipes.
âą Protective Equipment: Wear protective gloves and safety goggles during handling and dilution. Wear respiratory protection during all sanding stages.
âą Cleaning: Clean tools and brushes thoroughly with water immediately after use before the material starts drying. For dried residue, clean tools with acetone or wipes.
How did we do?
DC - Titan Topsealer (ENG)