Skip to main content

FC - Forshield PA Clear (ENG)

Fast-curing polyaspartic sealer for heavy-wear floors, topcoated for a satin finish.

tomas martinsson
Updated by tomas martinsson
Guide / Topcoat & Sealing

Forcrete — Forshield PA Clear

Practical guide and product specifications for finishing with heavy-duty polyaspartic protective sealer.

💡 About Forshield PA Clear:
Forshield PA is a two-component, fast-curing polyaspartic sealer providing extreme mechanical resistance and surface protection. It dries to a gloss finish as an initial base build layer and is subsequently overcoated with Forshield 2KWB or Forshield Ultra to achieve the desired satin-matte finish.
  • Smooth Floors (Roller Application): Applied to high-traffic floor areas requiring an ultra-durable protective foundation prior to final matte topcoating.
  • Bathrooms & Wet Areas (Troweling with Flakes): Mandatory base protective coat over Microstone and Microgranite in wet room installations. The product is blended with 4% Thickening Powder and troweled to fill the interstitial voids between flakes.
  • System Build-up: Forshield PA acts as a high-build intermediate protective coat (Coat 1) and is always sealed with Forshield 2KWB or Forshield Ultra as the final finish (Coat 2).
📱 Coverage & Mixing Ratio:
• Mixing Ratio (by weight): 60 parts Component A to 40 parts Component B (60 : 40).
• Coverage for Roller Application (Smooth Floors): Approx. 60 g/m².
• Coverage for Trowel Application (Flakes in Wet Areas): Approx. 120 g/m² (add 4% Thickening Powder).
Always use the mixing app to calculate exact quantities and batch proportions for your project.
⚠️ Important Information Before Starting:
• Working Temperature: Material, substrate, and ambient temperatures must remain between +10 °C and +25 °C.
• Rapid Cure / Short Pot Life: The product has a usable pot life of only approx. 15 minutes after mixing. Sequence operations carefully and never mix more material than can be applied immediately.
• Critical Component A Handling: Dense active particles settle at the bottom of Component A. Always stir Component A thoroughly down to the bottom of the container before weighing if using partial units.

1. Substrate Preparation

1.
Drying Time: The substrate must have cured and dried for at least 18 hours prior to application.
2.
Vacuuming & Wiping: Vacuum and dry-mop the substrate meticulously. Wipe down the entire surface with a dry microfiber cloth to remove all residual dust and loose particles.

2. Mixing

🧪 Mixing Instructions:
1. Stir Component A thoroughly down to the bottom of the vessel before weighing.
2. Combine Component A and Component B (60 : 40 by weight) and mix for 2–3 minutes with a mechanical paddle mixer at low speed.
3. For troweling over flakes (Microstone/Microgranite): Add 4% Thickening Powder to the A+B mixture and mix for an additional 2–3 minutes until completely smooth, uniform, and gel-like.

3. Application & Technique

1.
Smooth Floors (Roller Application – approx. 60 g/m²): Roll the sealer out very thinly using a fine-pile roller approved for epoxy/polyaspartic coatings (do not use the Microstar roller). Applying too thick a coat will cause micro-bubbling and create an unsightly plastic texture.
2.
Flakes in Bathrooms (Troweling – approx. 120 g/m²): Trowel the thickened mixture firmly across the surface using a rubber squeegee or flexible trowel to pack the voids between the flakes fully. Scrape off excess cleanly to prevent ridges and high spots.
3.
Curing Time: Allow Forshield PA to cure for a minimum of 3 hours before applying the final topcoat.

Next Steps: Topcoat Sealer

After at least 3 hours of curing time, roll a final coat of Forshield 2KWB or Forshield Ultra to reduce the sheen to satin-matte and ensure final wear and chemical resistance:

🛑 Health & Safety Equipment:
• Wear chemical-resistant nitrile gloves and safety goggles during all handling and mixing.
• Ensure continuous, adequate workspace ventilation throughout application and curing.
• Clean tools immediately with suitable solvents/thinners or use disposable tools.
• For professional trade use only. Protect from freezing and keep out of reach of children.

Documents & Technical Datasheets

📄 Technical Documentation: Forcrete Forshield PA Clear

How did we do?

FC - Forshield FX (ENG)

FC - Microbase XT (ENG)