Skip to main content

FC - Sanding Guide (ENG)

Which grit and which tool to use at each stage with Forcrete, from the substrate to the last coat before sealer.

tomas martinsson
Updated by tomas martinsson
Tradesperson Guide / Sanding Technique

Forcrete — Sanding Guide for All Coats

Comprehensive overview of sandpaper selection, sanding discs, and procedures from substrate preparation through final finish.

💡 Key Rules for Sanding Forcrete:
• Substrate preparation dictates the end result: A meticulously prepared substrate establishes the necessary foundation for the entire build-up.
• Precision across base coats: Following base coats, all transitions, internal corners, and external edges must be true and planar. A clean, flat surface at this stage ensures subsequent coats apply faster, spread evenly, and deliver a superior finish.
• Intermediate coats: Sanding between coats requires minimal effort when trowel application is consistent and smooth. If ridges or trowel lines develop, grind or sand them flat before continuing.
• Dust extraction: Vacuum and tack-mop the substrate meticulously between every sanding step to avoid dragging loose grit across the work.

Quick Guide: Grit Selection by Stage

Stage / Material Tooling & Abrasive Purpose / Notes
Ceramic & Porcelain Tiles Concrete grinder (Diamond cup wheel) Keying tile glaze and grinding down edge lippage and high spots.
Self-Leveling Screed / Concrete 24–40 grit silicon carbide (our black discs) Removes surface laitance and slurry skin to ensure mechanical bond.
Forprime DPM (Coat 1) 24–40 grit silicon carbide (our black discs) Keys the resin surface and denibs irregularities prior to next coat.
Forprime EPST, HB / FL (Coat 1) Concrete grinder (30 grit diamond segments, Medium bond) Creates a planar base plane. Work carefully if unreinforced!
Microbase XT, Coarse (Coat 1), HB/FL (Coat 2), Monostone XL (Coat 1/2), Trowel X Base 24–40 grit silicon carbide (our black discs) or 50 grit diamond pad (our neon green pads) Removes trowel marks. Essential to square corners and edges. At least one Monostone XL coat must be thoroughly sanded to prevent mesh ghosting.
Final Coat Coarse, Final Coat Monostone / Rockplaster XL/L, Trowel X L Fast pass with 50 grit diamond pad + thorough pass with 100 grit diamond pad (or 100 grit only) Defines texture level (heavier sanding yields more aggregate contrast). Sand uniformly to avoid patchy spots over undulating substrates.
Microquartz Medium Fast pass with 100 grit diamond pad + thorough pass with 200 grit diamond pad Removes imperfections and minor defects before sealing.
Microquartz Smooth 200 grit diamond pad Cleans up irregularities to produce an ultra-smooth, fine-grain surface.
Microstone & Microgranite (Flakes) 60–80 grit silicon carbide (our black discs), polished subsequently with 100 grit diamond pad Knocks down proud/loose flakes and levels surface prior to pore filling/sealing.

1. Substrate & Primer Sanding

•
Tiles & Pavers (Concrete Grinder): Grind using a diamond cup wheel, 30 grit or coarser. This removes tile glaze to promote optimal primer keying while cutting down proud tile lippage to establish a flat plane.
•
Screed & Concrete (24–40 grit silicon carbide – our black discs): Run over the surface to grind away cement laitance and weak surface skin. This guarantees deep penetration and mechanical adhesion for primers and subsequent cement coats.
•
Forprime DPM Coat 1 (24–40 grit silicon carbide – our black discs): Sand the cured epoxy lightly with coarse paper to de-nib high points and key the surface.

2. Base Coats & Intermediate Coats

•
Initial Coat EPST / HB / FL (Diamond grinder with 30 grit segments, Medium bond): Grind the first coat with a concrete grinder to establish a true floor plane. This step locks in surface tolerances for all subsequent layers. Caution: When grinding unreinforced EPST, grind with light pressure to avoid cutting into the screed or concrete substrate below.
•
Intermediate Coats (Microbase XT, Coarse Coat 1, HB/FL Coat 2, Monostone XL Coat 1 or 2, Trowel X Base): Sand with 24–40 grit silicon carbide (our black discs) or 50 grit diamond pads (our neon green pads) to eliminate ridges and lippage. Ensure perimeter edges and corners are square and crisp. At least one coat of Monostone XL must be sanded meticulously flat so mesh patterns never telegraph into finish layers.

3. Decorative Finish Coats

•
Final Coat Coarse, Final Coat Monostone / Rockplaster XL/L, Trowel X L: Sand rapidly with a 50 grit diamond pad followed by a controlled, thorough pass with a 100 grit diamond pad (or execute with 100 grit alone). Coarse finishes depend directly on sanding depth: heavier sanding exposes aggregate contrast for a rustic profile, while excessive sanding over uneven substrates can introduce blotchiness. Light, even passes with a tighter trowel technique produce a calm, subtle look.
•
Microquartz Medium: Execute a fast pass with a 100 grit diamond pad, followed by a careful pass with a 200 grit diamond pad to eliminate surface defects and burrs.
•
Microquartz Smooth: Sand with a 200 grit diamond pad to remove imperfections and create a uniform, refined surface.
•
Microstone & Microgranite (Flakes): Sand with 60–80 grit silicon carbide (our black discs) to de-nib proud/loose flakes and flatten the profile, then burnish with a 100 grit diamond pad before sealing or pore filling.
🛑 Health & Safety:
• Always wear an approved particulate respirator (minimum FFP3/P3 filter) during all sanding operations.
• Wear safety goggles and hearing protection when operating mechanical sanders or grinders.
• Connect power tools directly to an industrial dust extractor certified for hazardous dust (H-Class vacuum).
• Maintain active ventilation within the workspace.

How did we do?

FC - Mixing and Pigmentation (ENG)